Rigid stainless liners
A rigid liner is heavier and smoother inside and holds up to frequent cleaning.
A sweep in Willow Street can reline an unlined or damaged flue so smoke and gases vent safely from a fireplace, stove, insert, furnace or water heater. Dial (223) 244-3839 to talk with a local chimney pro about relining.
The liner is what smoke travels through on its way out of the house. Without one, heat and acidic condensation attack the masonry, and gaps can let heat or carbon monoxide escape into the home. Some older chimneys were built unlined, and others have clay tiles that have cracked over the decades.
Relining usually comes up for one of a handful of reasons. The original clay tiles may be cracked from age, settling or a chimney fire, or the chimney may never have been lined. Installing an insert, stove or high efficiency furnace often means the old flue is the wrong size.
Before relining, the chimney should get a thorough inspection, usually a Level 2 inspection with a camera run up the flue. That reveals whether the existing tiles can be repaired or need to be replaced, and it shows the route a new liner will take. Seeing the inside of the flue makes the decision much easier.
Chimney Liner Installation is often paired with chimney liner repair and chimney inspection, depending on the cause.
Looking for Willow Street chimney liner installation? Call (223) 244-3839 to reach a nearby chimney sweep.
Call nowA liner has to fit the flue, the appliance and the chimney route.
The inside of the chimney is checked so the route and condition are known. This confirms what kind of liner the chimney needs.
Sizing follows the appliance it will serve, since too big or too small both cause problems. The length is measured from the appliance to the top of the chimney.
Before the liner goes in, the chimney is swept and cleared. Tight flues sometimes need old tiles removed.
The stainless liner is lowered from the roof down to the appliance, often wrapped in an insulation blanket. Insulating it helps draft and reduces creosote and condensation.
A tee or connector joins the liner to the appliance, and a top plate seals the crown. Every joint is secured so gases stay inside the liner.
The appliance is fired or the draft is tested to confirm smoke and gases go up and out. Keep carbon monoxide alarms on every level of the home.
A rigid liner is heavier and smoother inside and holds up to frequent cleaning.
A poured liner fills gaps and creates a new flue in a single solid lining.
A properly sized liner for a water heater left alone after a furnace upgrade so the appliance drafts and the masonry stays dry.
Insulation is wrapped around the liner or poured into the space around it which improves draft and limits creosote.
Flexible stainless steel liners bend around offsets in the chimney which makes them the most common relining choice.
Most relining jobs use stainless steel, which handles high heat and corrosive flue gases well. It comes in flexible coils for chimneys with bends and rigid sections for straight flues. The grade of stainless and the wall thickness are matched to the fuel, and systems are tested and listed as complete kits with their parts.
Insulation around the liner helps flue gases rise and keeps the outside of the chimney cooler. A cap and top plate finish the job at the top of the chimney. In Willow Street, a stainless liner is a common upgrade when installing an insert or wood stove.
A chimney is relined when the existing flue cannot safely vent the appliance. Changing to an insert or stove, finding cracked tiles or recovering from a chimney fire usually leads to relining. Relining is usually far less disruptive than rebuilding the chimney.
When you call (223) 244-3839, tell the sweep what vents into the chimney, such as a fireplace, stove, furnace or water heater. If the furnace was upgraded recently, the water heater may now be venting into a flue that is too large. Relining with the right size solves the draft and moisture problems.
Many chimneys in Willow Street were built long before modern liners were standard. Across Willow Street and nearby towns such as Conestoga, Lancaster, Strasburg and Millersville, long heating seasons and repeated freeze and thaw cycles are hard on clay tile and mortar, which is why relining is one of the most common chimney upgrades in the area.
For chimney liner installation in Willow Street, PA or nearby towns like Conestoga, Lancaster, Strasburg and Millersville, call (223) 244-3839 to reach a chimney sweep who covers your street.
Winters here are long and cold, and the heating season usually runs from October well into April. The hardest thing on brick here is not the cold itself but the constant swing above and below freezing: water soaks into brick, mortar joints and the crown on a mild day, freezes overnight and expands, and each winter widens the cracks a little more. Wind driven rain from coastal storms finds any gap in flashing, too. Most homeowners in Willow Street, PA schedule a sweep in early fall, and a repair check after a hard winter.
Small chimney problems caught early usually stay small repairs.
Chimney sweeps in Willow Street know the chimneys and fireplaces common in local homes.
Ask the sweep about the cause, the options and the estimate before work starts.
More questions? Call (223) 244-3839
Repairing cracked clay flue tiles, open joints and damaged liners with resurfacing, joint repair or partial replacement.
Learn moreAn annual look at the flue, firebox, damper, crown and cap to catch cracks, blockages and leaks before they turn into hazards.
Learn moreFitting a fireplace insert so an open fireplace becomes a real heat source, with the chimney inspected before anything goes in.
Learn moreSetting up a new wood stove from hearth pad to chimney cap, so the stove drafts well and stays clear of anything that can burn.
Learn moreLooking for something else?
See all chimney servicesCall (223) 244-3839 for a local chimney sweep in Willow Street and nearby towns.
Free to call. No forms to fill out.